
ASTM A320 Low-Temperature Bolting
ASTM A320 covers alloy steel and stainless steel bolting for low-temperature service, such as studs on cold-service flanges, LNG equipment and refrigeration plant. The common grades are L7, L7M and L43 in alloy steel, and B8 and B8M in stainless steel. What sets A320 apart is the impact test: the alloy grades must stay tough at temperatures well below zero.
A320 bolting from Eastwood
- Studs and bolts to A320 L7, L7M, L43, B8 and B8M, made to your drawing
- Heat treatment done in house or by outside heat treaters, to the grade's requirements
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
Grades
| Grade | Material | Notes |
|---|---|---|
| L7 | Chromium-molybdenum steel (4140 type) | Quenched and tempered; the cold-service counterpart of A193 B7 |
| L7M | Same steel as L7 | Tempered to a lower hardness, 235 HBW max |
| L43 | Nickel-chromium-molybdenum steel (4340 type) | Quenched and tempered; used up to 4 in. diameter |
| B8, B8M | 304 and 316 stainless | Class 1 carbide solution treated; Class 2 strain hardened |
Strength
| Grade | Diameter (in.) | Tensile, min (ksi) | Yield, min (ksi) | Elongation, min (%) | Reduction of area, min (%) | Hardness, max |
|---|---|---|---|---|---|---|
| L7 | 2-1/2 and under | 125 | 105 | 16 | 50 | 321 HBW or 35 HRC |
| L7M | 2-1/2 and under | 100 | 80 | 18 | 50 | 235 HBW or 99 HRB |
| L43 | 4 and under | 125 | 105 | 16 | 50 | 321 HBW or 35 HRC |
| B8, B8M Class 1 | All | 75 | 30 | 30 | 50 | 223 HBW or 96 HRB |
Minimum tempering temperature is 1100°F for L7 and L43 and 1150°F for L7M. B8 and B8M Class 2 (strain hardened) have their own strength table that steps down by diameter; check the standard for your size.
Impact testing
| Grade | Charpy test temperature | Minimum energy, average of three 10 mm specimens |
|---|---|---|
| L7, L43 | -150°F (-101°C) | 20 ft-lbf (27 J) |
| L7M | -100°F (-73°C) | 20 ft-lbf (27 J) |
| B8, B8M Class 1 | Not required | |
| B8, B8M Class 2 | See current edition |
The test temperature on the drawing or the purchase order must be at or below the coldest the joint will see. If your design temperature is colder than the grade's standard test temperature, say so on the request.
Chemistry
| Element (%) | L7 | L43 |
|---|---|---|
| Carbon | 0.38 to 0.48 | 0.38 to 0.43 |
| Manganese | 0.75 to 1.00 | See current edition |
| Phosphorus, max | 0.035 | 0.035 |
| Sulfur, max | 0.040 | 0.040 |
| Silicon | 0.15 to 0.35 | 0.15 to 0.35 |
| Chromium | 0.80 to 1.10 | 0.70 to 0.90 |
| Nickel | 1.65 to 2.00 | |
| Molybdenum | 0.15 to 0.25 | 0.20 to 0.30 |
L7M has the same chemistry as L7. Check L43 manganese against the edition on your order.
Matching nuts
| A320 stud | Usual A194 nut |
|---|---|
| L7, L43 | Grade 7 |
| L7M | Grade 7M |
| B8 | Grade 8 |
| B8M | Grade 8M |
Older tables list A194 Grade 4 for L7. Grade 4 was withdrawn in 2017; Grade 7 is the usual nut now. Nuts for cold service have their own testing requirements, so order them with the studs and tell us the service temperature. See ASTM A194 nuts.
Grade marks
Each A320 stud is stamped on one end with its grade symbol and the manufacturer's mark. On a headed bolt the marks are on the head.
A320 or A193
L7 and A193 B7 use the same kind of steel and have the same strength up to 2-1/2 in. The difference is the impact test. B7 has none; L7 must pass it at -150°F. B7 has no impact requirement, so its toughness in deep cold is not proven, and that is why cold-service joints call for A320. For hot service, use A193.
A320 or A193
| Specification | Service | Common grade | Minimum tensile (ksi) |
|---|---|---|---|
| A193 | High temperature or high pressure | B7 | 125 to 2-1/2 in. |
| A320 | Low temperature, impact tested | L7 | 125 to 2-1/2 in. |
| A453 | High temperature, superalloy | 660 (A286) | 130 |
| A354 | General, quenched and tempered alloy | BD | 150 |
| A307 | General, carbon steel | A | 60 |
Common questions
What is ASTM A320 L7?
A320 Grade L7 is chromium-molybdenum alloy steel bolting, quenched and tempered, for low-temperature service. It has 125 ksi minimum tensile strength up to 2-1/2 in. and must pass a Charpy impact test at -150°F.
What is the difference between A320 L7 and A193 B7?
Same kind of steel and the same strength up to 2-1/2 in. L7 must also pass an impact test at -150°F, which makes it suitable for cold service. B7 has no impact test.
What temperature is A320 L7 impact tested at?
-150°F (-101°C) for L7 and L43, and -100°F (-73°C) for L7M.
What nut goes with an A320 L7 stud?
An A194 Grade 7 heavy hex nut. L7M takes Grade 7M.
What is L7M used for?
L7M is L7 tempered to a lower hardness, 235 HBW maximum, for low-temperature joints that also need a hardness limit, such as sour service.
What is A320 material?
Alloy steel and stainless steel bolting for low temperature service. L7 is chromium-molybdenum alloy steel; B8 and B8M are stainless.
What material is ASTM A320 L7 equivalent to?
L7 is a chromium-molybdenum steel of the AISI 4140 type, the same family as A193 B7, with impact testing for low temperature service.
Sizes Eastwood makes
We machine studs from bar up to 3.000 in. diameter, with small diameters on our Swiss machines. Hex bolts and cap screws are smaller, because the head sets the bar size. Larger parts are quoted too.
Related pages
ASTM A193 · A193 Grade B7 · ASTM A194 nuts · Industrial studs · Oil and gas · Chemical and refining · Quality, certifications and PPAP
Industries that use this spec: Chemical Refining · Oil and Gas
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · A193 Grade B7 · ASTM A194 nuts · ASTM A453 Grade 660 · ASTM A354 · ASTM F593 and F594 · SAE J429 Grades 5 and 8 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers · ASTM A490 structural bolts
Quote A320 bolting
Send the grade, diameter, length, thread, quantity and the lowest service temperature, or send the print. Add any coating, testing, PPAP or sour-service requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize requirements from ASTM A320/A320M. The standard itself governs. Check the current edition for your order.