
ASTM A490 Structural Bolts
A490 is the 150 ksi heavy hex structural bolt, 1/2 to 1-1/2 in. diameter, quenched and tempered alloy steel. ASTM withdrew A490 as its own standard in 2016. It is now Grade A490 of ASTM F3125, which also covers A325 and the twist-off F1852 and F2280 bolts.
A490 bolts from Eastwood
- Heavy hex structural bolts to F3125 Grade A490 and special lengths made to your drawing
- Heat treatment done in house or by outside heat treaters, to the grade's requirements
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
A490 is now F3125
| Former standard | Now | Minimum tensile | Head |
|---|---|---|---|
| A325 | F3125 Grade A325 | 120 ksi | Heavy hex |
| A490 | F3125 Grade A490 | 150 ksi | Heavy hex |
| F1852 | F3125 Grade F1852 | 120 ksi | Twist-off |
| F2280 | F3125 Grade F2280 | 150 ksi | Twist-off |
Drawings and orders still say A490. The bolt is still marked A490.
Strength and hardness
| Property | Grade A490 |
|---|---|
| Size | 1/2 to 1-1/2 in. |
| Tensile | 150 ksi min, 173 ksi max |
| Yield, min | 130 ksi |
| Proof load stress | 120 ksi |
| Elongation, min | 14% |
| Reduction of area, min | 40% |
| Core hardness | C33 to C38 HRC |
The 173 ksi maximum and the hardness cap exist to limit the risk of hydrogen embrittlement in a high strength part.
Type 1 and Type 3
| Type | Material |
|---|---|
| 1 | Alloy steel or alloy steel with boron |
| 3 | Weathering steel, for exposed steel that is left unpainted |
Coatings
A490 bolts may not be hot-dip galvanized, mechanically galvanized or zinc electroplated, because of the hydrogen embrittlement risk. Only the zinc-flake coatings that F3125 lists for Grade A490 are permitted. These now fall under ASTM F3393 (corrosion class D, appearance class 1, friction class R), which replaced F1136, F2833 and F3019. Where galvanized bolts are needed, A325 is the usual choice. Check the current F3125 edition for the coatings it lists.
Nuts and washers
| Component | Type 1 bolt | Type 3 bolt |
|---|---|---|
| Nut | A563 Grade DH heavy hex, or A194 Grade 2H | A563 Grade DH3 heavy hex |
| Washer | F436 Type 1 | F436 Type 3 |
Strength compared
A490 compared
| Specification | Typical part | Minimum tensile (ksi) | Heat treated | Size range (in.) |
|---|---|---|---|---|
| A307 Grade A | Bolts, studs, threaded rod | 60 | No | 1/4 to 4 |
| SAE J429 Grade 5 | Bolts, screws, studs | 120 to 1 in.; 105 above | Yes | Up to 1-1/2 |
| A449 | Bolts, studs, any shape | 120 to 1 in.; 105; 90 above 1-1/2 | Yes | 1/4 to 3 |
| F3125 Grade A325 | Heavy hex structural bolts | 120 | Yes | 1/2 to 1-1/2 |
| SAE J429 Grade 8 | Bolts, screws, studs | 150 | Yes | Up to 1-1/2 |
| A354 Grade BD | Bolts, studs | 150 | Yes | 1/4 to 4 |
| F3125 Grade A490 | Heavy hex structural bolts | 150 (173 max) | Yes | 1/2 to 1-1/2 |
| A574 | Socket head cap screws | 180 to 1/2 in.; 170 above | Yes | #0 to 4 |
Metric equivalent
The metric grade is F3125 Grade A490M, 1,040 MPa minimum tensile.
| Inch grade | Closest metric class | Metric minimum tensile |
|---|---|---|
| SAE J429 Grade 5, A449 and F3125 A325 | 8.8 | 800 MPa to M16, 830 MPa above (about 116 to 120 ksi) |
| SAE J429 Grade 8, A354 BD and F3125 A490 | 10.9 | 1,040 MPa (about 151 ksi) |
| A574 socket head cap screws | 12.9 | 1,220 MPa (about 177 ksi) |
The pairs are close in strength, not interchangeable. Metric and inch threads do not mix, and the standards test and mark differently. Grade 5 and A449 match class 8.8 only up to 1 in.; above that they fall below it.
Common questions
Is ASTM A490 still a current standard?
Not on its own. ASTM withdrew it in 2016 and A490 bolts are now Grade A490 of ASTM F3125.
What is the tensile strength of an A490 bolt?
150 ksi minimum and 173 ksi maximum, with 130 ksi minimum yield, from 1/2 to 1-1/2 in.
Can A490 bolts be galvanized?
No. Hot-dip and mechanical galvanizing are not permitted because of hydrogen embrittlement. The zinc-flake coatings F3125 lists for Grade A490 (now ASTM F3393) are.
What nut goes with an A490 bolt?
An A563 Grade DH heavy hex nut, or A194 Grade 2H. Type 3 bolts take A563 Grade DH3.
What is the difference between A325 and A490?
A325 is 120 ksi minimum tensile and can be galvanized. A490 is 150 ksi and cannot be hot-dip or mechanically galvanized.
What ASTM bolt grade is equivalent to A490?
A354 Grade BD and SAE J429 Grade 8 in strength, all 150 ksi minimum tensile. The metric grade is F3125 Grade A490M.
Is A490 grade 8?
No. They share the same minimum tensile and yield, but A490 is a structural bolt with heavy hex dimensions, testing and coating rules of its own.
What are A490 bolts used for?
High strength structural steel connections in buildings and bridges, where fewer or smaller bolts than A325 are wanted. Slip critical and bearing type joints both use them.
Sizes Eastwood makes
F3125 Grade A490 covers 1/2 to 1-1/2 in. heavy hex bolts. We make them to your length and thread length, along with matching DH nuts and F436 washers.
Related pages
Hex head cap screws · Custom bolts · Specialty nuts · Washers · Quality, certifications and PPAP
Industries that use this spec: Power Generation
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · A193 Grade B7 · ASTM A194 nuts · ASTM A320 · ASTM A453 Grade 660 · ASTM A354 · ASTM F593 and F594 · SAE J429 Grades 5 and 8 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers
Quote A490 bolts
Send the diameter, length, type, finish and quantity, or send the print. Add any coating, testing or PPAP requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize requirements from ASTM F3125 Grade A490. The standard itself governs. Check the current edition for your order.