ASTM A449 covers quenched and tempered steel bolts, studs and other externally threaded fasteners from 1/4 to 3 in. diameter. It is the larger-size counterpart of SAE J429 Grade 5, at 120 ksi minimum tensile up to 1 in., and it is not limited to any head style.

A449 parts from Eastwood

  • Bolts, studs and threaded rod to A449, in the configuration on your drawing
  • Heat treatment done in house or by outside heat treaters, to the grade's requirements
  • Material certifications with heat numbers shipped with the order
  • PPAP documentation at Levels 1 to 5, for a fee
  • An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
Request a quote

What A449 is

A449 is medium carbon steel, quenched and tempered. Strength steps down with diameter, at 1 in. and again at 1-1/2 in. Above 1-1/2 in. it is the usual call where a drawing would use Grade 5 at a smaller size.

Strength and hardness

Size (in.)Proof load (ksi)Yield, min (ksi)Tensile, min (ksi)Elongation, min (%)Reduction of area, min (%)Hardness
1/4 to 185921201435C25 to C34
Over 1 to 1-1/274811051435C19 to C30
Over 1-1/2 to 35558901435B91 to B100

Strength by size

ksiA449 minimum strength5060708090100110120130011-1/223Diameter, in.Tensile: 120, 105 and 90 ksiTensileYield: 92, 81 and 58 ksiYield
A449 strength drops at 1 in. and again at 1-1/2 in. A 2 in. A449 stud is a 90 ksi part. Solid line is tensile, dashed line is yield.

Chemistry

A449 may be carbon steel, carbon boron steel, alloy steel or alloy boron steel. Carbon is 0.30 to 0.52% and manganese 0.60% minimum for all four. Phosphorus and sulfur limits depend on the steel type.

Nuts and washers

FinishSize (in.)Usual nut
Plain1/4 to 1-1/2A563 Grade B hex
PlainOver 1-1/2 to 3A563 Grade A heavy hex
Galvanized1/4 to 3A563 Grade DH heavy hex

Nuts of a higher grade are also suitable. The usual washer is F436.

Strength compared

A307 Grade AA307 Grade A: 60 ksi minimum tensile60SAE J429 Grade 5 (to 1 in.)SAE J429 Grade 5 (to 1 in.): 120 ksi minimum tensile120A449 (to 1 in.)A449 (to 1 in.): 120 ksi minimum tensile120A193 B7 (to 2-1/2 in.)A193 B7 (to 2-1/2 in.): 125 ksi minimum tensile125A354 BC (to 2-1/2 in.)A354 BC (to 2-1/2 in.): 125 ksi minimum tensile125SAE J429 Grade 8SAE J429 Grade 8: 150 ksi minimum tensile150A354 BDA354 BD: 150 ksi minimum tensile150A490A490: 150 ksi minimum tensile150A574 (to 1/2 in.)A574 (to 1/2 in.): 180 ksi minimum tensile180
A449 matches SAE J429 Grade 5 up to 1 in. Minimum tensile strength in ksi.

A449 or A325

A449 and A325 (now ASTM F3125 Grade A325) share the same strength up to 1 in. They are not interchangeable. A325 is a structural bolt with fixed heavy hex dimensions, a 1-1/2 in. size limit and its own testing. A449 is a general standard that covers studs and other shapes and goes to 3 in. Substituting one for the other in a structural joint needs engineering approval.

A449 compared

SpecificationTypical partMinimum tensile (ksi)Heat treatedSize range (in.)
A307 Grade ABolts, studs, threaded rod60No1/4 to 4
SAE J429 Grade 5Bolts, screws, studs120 to 1 in.; 105 aboveYesUp to 1-1/2
A449Bolts, studs, any shape120 to 1 in.; 105; 90 above 1-1/2Yes1/4 to 3
F3125 Grade A325Heavy hex structural bolts120Yes1/2 to 1-1/2
SAE J429 Grade 8Bolts, screws, studs150YesUp to 1-1/2
A354 Grade BDBolts, studs150Yes1/4 to 4
F3125 Grade A490Heavy hex structural bolts150 (173 max)Yes1/2 to 1-1/2
A574Socket head cap screws180 to 1/2 in.; 170 aboveYes#0 to 4

Metric equivalent

Inch gradeClosest metric classMetric minimum tensile
SAE J429 Grade 5, A449 and F3125 A3258.8800 MPa to M16, 830 MPa above (about 116 to 120 ksi)
SAE J429 Grade 8, A354 BD and F3125 A49010.91,040 MPa (about 151 ksi)
A574 socket head cap screws12.91,220 MPa (about 177 ksi)

The pairs are close in strength, not interchangeable. Metric and inch threads do not mix, and the standards test and mark differently. Grade 5 and A449 match class 8.8 only up to 1 in.; above that they fall below it.

Common questions

What is ASTM A449?

The standard for quenched and tempered steel bolts, studs and other externally threaded fasteners from 1/4 to 3 in. It is 120 ksi minimum tensile up to 1 in.

Is A449 the same as Grade 5?

Up to 1 in. the strength is the same. A449 goes up to 3 in., where SAE J429 stops at 1-1/2 in., so A449 is the usual call for large Grade 5 parts.

What is the tensile strength of A449?

120 ksi up to 1 in., 105 ksi over 1 to 1-1/2 in., and 90 ksi over 1-1/2 to 3 in.

What nut goes with an A449 bolt?

A563 Grade B hex up to 1-1/2 in. and Grade A heavy hex above, plain. Galvanized A449 takes A563 Grade DH heavy hex nuts.

Can A449 replace A325 bolts?

Not without engineering approval. A325 is a structural bolt standard with fixed dimensions and testing that A449 does not require.

What is ASTM A449 material?

Medium carbon steel, carbon boron steel, alloy steel or alloy boron steel, quenched and tempered.

Is A449 stronger than A325?

No. Both are 120 ksi minimum tensile up to 1 in. Above 1 in., A449 drops to 105 and then 90 ksi, while F3125 Grade A325 stays at 120 ksi to 1-1/2 in.

What is an A490 bolt equivalent to?

In strength, SAE J429 Grade 8 and A354 Grade BD, all 150 ksi minimum tensile. A490 is a structural bolt with its own testing, so substitution needs engineering approval.

Sizes Eastwood makes

A449 covers up to 3 in. We machine bolts and studs from bar up to 3.000 in. diameter, with small diameters on our Swiss machines.

Industrial studs · Custom bolts · Hex head cap screws · Power generation · Quality, certifications and PPAP

Quote A449 parts

Send the diameter, length, thread, finish and quantity, or send the print. Add any coating, testing or PPAP requirement and the date you need the parts. Lead time comes back with the price.

Request a quote sales@emfasteners.com

The tables summarize requirements from ASTM A449. The standard itself governs. Check the current edition for your order.