
ASTM A354 Grade BC and BD Bolts
ASTM A354 covers quenched and tempered alloy steel bolts, studs, threaded rod and other externally threaded fasteners up to 4 in. diameter, for service at normal atmospheric temperatures where high strength is needed. It has two grades, BC and BD. BD is the high-strength grade, often used for anchor rods and large bolts.
A354 bolting from Eastwood
- Bolts, studs and threaded rod to A354 BC or BD, in the configuration on your drawing
- Heat treatment done in house or by outside heat treaters, to the grade's requirements
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
Grades
| Grade | What it is |
|---|---|
| BC | Quenched and tempered alloy steel, 125 ksi minimum tensile up to 2-1/2 in. |
| BD | Quenched and tempered alloy steel, 150 ksi minimum tensile, with a maximum tensile and hardness limit |
Neither grade restricts the shape of the part, so A354 covers headed bolts, studs, bent anchor rods and threaded rod. For high-temperature service, use A193.
Strength and hardness
| Grade | Size (in.) | Tensile (ksi) | Proof stress (ksi) | Yield, min (ksi) | Elongation, min (%) | Reduction of area, min (%) | Hardness |
|---|---|---|---|---|---|---|---|
| BC | 1/4 to 2-1/2 | 125 min | 105 | 109 | 16 | 50 | 26 to 36 HRC |
| BC | Over 2-1/2 to 4 | 115 min | 95 | 99 | 16 | 45 | 22 to 33 HRC |
| BD | 1/4 to 4 | 150 min, 173 max | 120 | 130 | 14 | 40 | 33 to 38 HRC |
Proof stress is the stress a bolt must carry for a short time without permanent stretch. Proof load for a given size is the proof stress times the thread stress area.
Chemistry
| Grade | Size (in.) | Carbon (%) | Phosphorus, max (%) | Sulfur, max (%) |
|---|---|---|---|---|
| BC | Through 4 | 0.30 to 0.53 | See current edition | 0.040 |
| BD | Through 2-1/4 | 0.30 to 0.53 | See current edition | 0.040 |
| BD | Over 2-1/4 to 4 | 0.35 to 0.53 | See current edition | 0.040 |
The standard allows any alloy steel that meets the chemistry and mechanical requirements. Larger BD sizes carry added alloy requirements; check the current edition.
Matching nuts
| Bolt | Finish | Usual A563 nut |
|---|---|---|
| BC | Plain | Grade C, heavy hex |
| BC | Zinc coated | Grade DH, heavy hex |
| BD | Any | Grade DH, heavy hex |
Grade marks
A354 bolts and studs are marked BC or BD with the manufacturer's mark, on the head of a bolt or one end of a stud.
BD or A490
A354 BD has the same strength level as A490 structural bolts (now ASTM F3125 Grade A490). A490 is limited to heavy hex structural bolts up to 1-1/2 in.; A354 BD is not limited in shape and goes to 4 in. That is why BD is the usual call for anchor rods, threaded rod and large bolts. For pretensioned structural joints, the standard points engineers to the head size, nut, washer and testing requirements of F3125.
A354 compared
| Specification | Typical part | Minimum tensile (ksi) | Heat treated | Size range (in.) |
|---|---|---|---|---|
| A307 Grade A | Bolts, studs, threaded rod | 60 | No | 1/4 to 4 |
| SAE J429 Grade 5 | Bolts, screws, studs | 120 to 1 in.; 105 above | Yes | Up to 1-1/2 |
| A449 | Bolts, studs, any shape | 120 to 1 in.; 105; 90 above 1-1/2 | Yes | 1/4 to 3 |
| F3125 Grade A325 | Heavy hex structural bolts | 120 | Yes | 1/2 to 1-1/2 |
| SAE J429 Grade 8 | Bolts, screws, studs | 150 | Yes | Up to 1-1/2 |
| A354 Grade BD | Bolts, studs | 150 | Yes | 1/4 to 4 |
| F3125 Grade A490 | Heavy hex structural bolts | 150 (173 max) | Yes | 1/2 to 1-1/2 |
| A574 | Socket head cap screws | 180 to 1/2 in.; 170 above | Yes | #0 to 4 |
Metric equivalent
| Inch grade | Closest metric class | Metric minimum tensile |
|---|---|---|
| SAE J429 Grade 5, A449 and F3125 A325 | 8.8 | 800 MPa to M16, 830 MPa above (about 116 to 120 ksi) |
| SAE J429 Grade 8, A354 BD and F3125 A490 | 10.9 | 1,040 MPa (about 151 ksi) |
| A574 socket head cap screws | 12.9 | 1,220 MPa (about 177 ksi) |
The pairs are close in strength, not interchangeable. Metric and inch threads do not mix, and the standards test and mark differently. Grade 5 and A449 match class 8.8 only up to 1 in.; above that they fall below it.
Common questions
What is ASTM A354 Grade BD?
A354 Grade BD is quenched and tempered alloy steel bolting with 150 ksi minimum tensile strength, 130 ksi minimum yield and 33 to 38 HRC hardness, up to 4 in. diameter.
What is the difference between A354 BC and BD?
BD is stronger: 150 ksi minimum tensile against 125 ksi for BC up to 2-1/2 in. BD also has a maximum tensile strength and a narrower hardness range.
Is A354 BD the same as A490?
They have the same strength level, but A490 is limited to heavy hex structural bolts up to 1-1/2 in. A354 BD covers any configuration up to 4 in.
What nut goes with an A354 BD bolt?
An ASTM A563 Grade DH heavy hex nut. Plain BC bolts take A563 Grade C heavy hex nuts, and zinc-coated BC bolts take Grade DH.
Can A354 be used at high temperature?
A354 is meant for normal atmospheric temperatures, with limited elevated-temperature use. For high-temperature service, use A193.
What strength grade is ASTM A354 Grade BD equivalent to?
SAE J429 Grade 8 and F3125 Grade A490 in strength: 150 ksi minimum tensile and 130 ksi minimum yield. A354 BD covers sizes up to 4 in.
What grade is A354?
A354 is a quenched and tempered alloy steel bolt and stud standard with two grades: BC (125 ksi up to 2-1/2 in.) and BD (150 ksi).
What are the differences between A354 BD and Grade 8?
They have the same minimum strength. Grade 8 stops at 1-1/2 in.; A354 BD goes to 4 in. and covers studs and other shapes.
Sizes Eastwood makes
A354 covers up to 4 in. We machine bolts and studs from bar up to 3.000 in. diameter, with small diameters on our Swiss machines. Larger parts are quoted too.
Related pages
ASTM A193 · A193 Grade B7 · Industrial studs · Custom bolts · Power generation · Quality, certifications and PPAP
Industries that use this spec: Power Generation · Oil and Gas
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · A193 Grade B7 · ASTM A194 nuts · ASTM A320 · ASTM A453 Grade 660 · ASTM F593 and F594 · SAE J429 Grades 5 and 8 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers · ASTM A490 structural bolts
Quote A354 bolting
Send the grade, diameter, length, thread, finish and quantity, or send the print. Add any coating, testing, PPAP or sour-service requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize requirements from ASTM A354. The standard itself governs. Check the current edition for your order.