
ASTM A193 Grade B7 Studs
ASTM A193 Grade B7 is a chromium-molybdenum alloy steel bolting grade, quenched and tempered, for high-temperature and high-pressure service. It is the most common stud on flanges, valves and pressure vessels, and it is paired with A194 Grade 2H heavy hex nuts.
B7 studs from Eastwood
- Studs, bolts and threaded rod to A193 B7, made to the length and thread on your drawing
- Heat treatment done in house or by outside heat treaters, to the grade's requirements
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
What B7 is
| Item | A193 Grade B7 |
|---|---|
| Steel | Chromium-molybdenum alloy steel (AISI 4140, 4142 or 4145) |
| Condition | Quenched and tempered |
| Minimum tempering temperature | 1100°F (593°C) |
| Hardness, max | 321 HBW or 35 HRC |
| Usual nut | A194 Grade 2H heavy hex |
| Threads | UNC to 1 in., 8UN above |
| Low-temperature version | A320 Grade L7: same steel and strength up to 2-1/2 in., with impact testing |
Strength by diameter
MPa and mm figures are conversions of the inch values, rounded. The metric edition of the standard lists its own minimums, which differ slightly.
| Diameter (in.) | Tensile, min (ksi) | Yield, min (ksi) | Elongation, min (%) | Reduction of area, min (%) | Hardness, max |
|---|---|---|---|---|---|
| 2-1/2 and under | 125 | 105 | 16 | 50 | 321 HBW or 35 HRC |
| Over 2-1/2 to 4 | 115 | 95 | 16 | 50 | 321 HBW or 35 HRC |
| Over 4 to 7 | 100 | 75 | 18 | 50 | 321 HBW or 35 HRC |
Chemistry
| Element | Percent |
|---|---|
| Carbon | 0.38 to 0.48 |
| Manganese | 0.75 to 1.00 |
| Phosphorus, max | 0.035 |
| Sulfur, max | 0.040 |
| Silicon | 0.15 to 0.35 |
| Chromium | 0.80 to 1.10 |
| Molybdenum | 0.15 to 0.25 |
These are heat analysis limits from the current edition. A product check on finished parts is allowed a small variation (0.02 on carbon, 0.04 on manganese, 0.05 on chromium), and older editions printed slightly wider ranges such as carbon 0.37 to 0.49. If a mill cert sits just outside this table, check it against the edition on your order before rejecting it.
Tempering and temperature
B7 is quenched and then tempered at no less than 1100°F. A193 does not set a service temperature. That limit comes from the design code for the joint, such as ASME B31.1, B31.3 or Section VIII. As a rough guide, B7 is the usual choice up to about 750 to 850°F, and B16 is used above that. For low-temperature service the usual choice is A320 Grade L7.
Matching nut
| Stud | Usual nut |
|---|---|
| A193 B7 | A194 Grade 2H heavy hex |
| A193 B7M | A194 Grade 2HM heavy hex |
| A320 L7 | A194 Grade 7 heavy hex |
Order the nuts with the studs so the heat numbers and certifications travel together. See ASTM A194 nuts for the nut grades.
Grade marks
Each B7 stud is stamped on one end with "B7" and the manufacturer's mark. B7M is stamped "B7M". On a headed bolt the marks are on the head.
B7 or B7M
| B7 | B7M | |
|---|---|---|
| Steel | Cr-Mo alloy steel | Same steel |
| Minimum tempering | 1100°F | 1150°F |
| Tensile, min (to 2-1/2 in.) | 125 ksi | 100 ksi |
| Yield, min (to 2-1/2 in.) | 105 ksi | 80 ksi |
| Hardness, max | 321 HBW or 35 HRC | 235 HBW or 99 HRB |
| Hardness testing | Sample from the lot | Every stud tested |
| Typical use | General flange bolting | Sour service, where hydrogen sulfide is present |
B7M gives up strength for a hardness limit that sour-service rules work to. If your specification cites NACE MR0175 / ISO 15156 or NACE MR0103, it usually calls for B7M studs with 2HM nuts. Put the specification on the request so the testing and paperwork are quoted with the parts.
Coatings
Alloy steel studs ship plain unless the order calls for a coating. The common callouts are PTFE (fluoropolymer) coating, zinc plating and hot-dip galvanizing. A coated stud usually has a lower temperature rating than a plain one, so check the coating against the service temperature. Put the coating and its specification on the request and we quote it with the parts.
B7 compared
| Grade | Minimum tensile (ksi) | Minimum yield (ksi) | Made for |
|---|---|---|---|
| A193 B7, to 2-1/2 in. | 125 | 105 | High temperature and pressure |
| A193 B7M | 100 | 80 | Sour service, hardness limited |
| A320 L7, to 2-1/2 in. | 125 | 105 | Low temperature, impact tested |
| A193 B16, to 2-1/2 in. | 125 | 105 | Higher temperature than B7 |
| SAE J429 Grade 8 | 150 | 130 | General high strength, not for high temperature service |
Common questions
What is ASTM A193 B7?
A193 Grade B7 is chromium-molybdenum alloy steel bolting, quenched and tempered, for high-temperature or high-pressure service. Minimum tensile strength is 125 ksi up to 2-1/2 in. diameter.
What is the difference between B7 and B7M?
B7M is the same steel tempered to a lower hardness, 235 HBW maximum, and every piece is hardness tested. It is the grade used in sour service. B7 is stronger and is the general-purpose grade.
What nut goes with an A193 B7 stud?
An A194 Grade 2H heavy hex nut. B7M studs take A194 Grade 2HM nuts.
Is B7 the same as 4140?
B7 is made from 4140, 4142 or 4145 steel, but the grade also fixes the heat treatment, strength, hardness and testing. Plain 4140 bar is not B7 until it meets those requirements.
What is the tensile strength of B7?
125 ksi minimum up to 2-1/2 in. diameter, 115 ksi over 2-1/2 to 4 in., and 100 ksi over 4 to 7 in.
Is ASTM A193 grade B7 stainless steel?
No. B7 is a chromium-molybdenum alloy steel, quenched and tempered. The stainless grades in A193 are B8 (304) and B8M (316).
Is B7 as strong as grade 8?
No. B7 is 125 ksi minimum tensile up to 2-1/2 in.; SAE J429 Grade 8 is 150 ksi. B7 is made and tested for high temperature bolting, which Grade 8 is not.
Sizes Eastwood makes
We machine studs from bar up to 3.000 in. diameter, with small diameters on our Swiss machines. Hex bolts, cap screws and nuts are smaller, because the hex sets the bar size. Larger parts are quoted too.
Related pages
ASTM A193 (all grades) · ASTM A194 nuts · ASTM A320 low-temperature bolting · Industrial studs · Oil and gas · Chemical and refining · Quality, certifications and PPAP
Industries that use this spec: Oil and Gas · Chemical Refining · Power Generation
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · ASTM A194 nuts · ASTM A320 · ASTM A453 Grade 660 · ASTM A354 · ASTM F593 and F594 · SAE J429 Grades 5 and 8 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers · ASTM A490 structural bolts
Quote B7 studs
Send the diameter, length, thread, quantity and nut requirement, or send the print. Add any coating, testing, PPAP or sour-service requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize minimum requirements from ASTM A193/A193M. The standard itself governs. Check the current edition for your order.