
ASTM F593 and F594 Stainless Bolts and Nuts
ASTM F593 covers stainless steel bolts, hex cap screws and studs from 1/4 in. to 1-1/2 in. diameter for general corrosion resistance. ASTM F594 covers the matching stainless nuts. The most common callouts are F593C and F593G, which are cold-worked 304 and 316.
F593 and F594 parts from Eastwood
- Stainless bolts, cap screws, studs and nuts made to your drawing
- Stainless parts passivated in house
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
Alloy groups
F593 sorts stainless steels into alloy groups. Group 1 is the 304 family and Group 2 is the 316 family. Group 2 carries molybdenum and resists chlorides and pitting better, so it is the usual pick near salt water and in chemical service. The standard has further groups for other stainless steels; if your drawing calls for one, send it and we will quote it.
Conditions
| Condition | What it means |
|---|---|
| AF | Headed and rolled from annealed stock, then annealed again. Softest condition. |
| A | Machined from annealed or solution-annealed bar. |
| CW | Cold worked: headed and rolled from annealed stock. The most common condition. |
| SH | Strain hardened: machined from strain-hardened bar, or cold worked. Highest strength. |
Strength by condition
Groups 1 and 2 have the same strength requirements. Unlike most bolt specifications, F593 gives a tensile range, a minimum and a maximum.
| Condition | Size (in.) | Tensile (ksi) | Yield, min (ksi) | Hardness |
|---|---|---|---|---|
| AF | 1/4 to 1-1/2 | 65 to 85 | 20 | B85 max |
| A | 1/4 to 1-1/2 | 75 to 100 | 30 | B65 to B95 |
| CW | 1/4 to 5/8 | 100 to 150 | 65 | B95 to C32 |
| CW | 3/4 to 1-1/2 | 85 to 140 | 45 | B80 to C32 |
Condition SH
| Condition | Size (in.) | Tensile (ksi) | Yield, min (ksi) | Hardness |
|---|---|---|---|---|
| SH | 1/4 to 5/8 | 120 to 160 | 95 | C24 to C36 |
| SH | 3/4 to 1 | 110 to 150 | 75 | C20 to C32 |
| SH | 1-1/8 to 1-1/4 | 100 to 140 | 60 | B95 to C30 |
| SH | 1-3/8 to 1-1/2 | 95 to 130 | 45 | B90 to C28 |
Marks
F593 bolts are marked with a letter code that gives the alloy group and condition. The common marks:
| Mark | Alloy group | Condition |
|---|---|---|
| F593A | 1 (304 family) | AF |
| F593B | 1 (304 family) | A |
| F593C | 1 (304 family) | CW, 1/4 to 5/8 in. |
| F593D | 1 (304 family) | CW, 3/4 to 1-1/2 in. |
| F593E | 2 (316 family) | AF |
| F593F | 2 (316 family) | A |
| F593G | 2 (316 family) | CW, 1/4 to 5/8 in. |
| F593H | 2 (316 family) | CW, 3/4 to 1-1/2 in. |
F594 nuts
F594 is the nut standard that goes with F593. Use a nut from the same alloy group as the bolt, with a proof stress at least equal to the bolt's minimum tensile strength. A 316 bolt takes a 316-family nut.
F593 or A193 B8
Both can be 304 or 316 stainless. F593 is a general-purpose fastener standard for corrosion resistance, limited to 1-1/2 in. diameter, with tensile ranges. A193 B8 and B8M are pressure-vessel and flange bolting grades, with their own testing and marking, and they go larger. If the joint is on a flange, valve or vessel, the drawing will usually call for A193 B8 or B8M.
Common questions
What is ASTM F593?
ASTM F593 is the standard for stainless steel bolts, hex cap screws and studs from 1/4 to 1-1/2 in. diameter for general corrosion resistance. F594 covers the matching nuts.
What does F593C mean?
F593C is an alloy Group 1 (304 family) bolt in the cold-worked condition. F593G is the same condition in Group 2 (316 family).
What is the difference between F593 and A193 B8?
F593 is a general-purpose stainless fastener standard up to 1-1/2 in. A193 B8 is stainless bolting for pressure vessels, valves and flanges, with different testing and marking.
What nut goes with an F593 bolt?
An ASTM F594 nut from the same alloy group, with a proof stress at least equal to the bolt's minimum tensile strength.
What is the difference between CW and SH?
Both are cold-worked conditions. SH is strain hardened to a higher strength: 120 ksi minimum tensile up to 5/8 in., against 100 ksi for CW.
What is the ASTM F593 equivalent for bolts?
There is no current ASTM metric version; ASTM F738M was withdrawn in 2015. Metric stainless bolts are normally ordered to ISO 3506-1, for example A2-70 or A4-70. For flange and pressure bolting in stainless, A193 B8 and B8M are used instead of F593.
What grade of steel is the F593D bolt?
Alloy group 1, the 304 stainless family, in the cold worked condition, for sizes 3/4 to 1-1/2 in.
Sizes Eastwood makes
F593 covers 1/4 to 1-1/2 in. We machine stainless bolts and studs across that range, with small diameters on our Swiss machines. Larger stainless parts are made to A193 B8 or B8M or to your drawing.
Related pages
ASTM A193 (B8 and B8M) · Stainless steel fasteners · Hex head cap screws · Marine and naval · Water systems · Quality, certifications and PPAP
Industries that use this spec: Marine and Naval · Water Systems · Pharmaceutical · Pulp and Paper · Chemical Refining
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · A193 Grade B7 · ASTM A194 nuts · ASTM A320 · ASTM A453 Grade 660 · ASTM A354 · SAE J429 Grades 5 and 8 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers · ASTM A490 structural bolts
Quote F593 and F594 parts
Send the alloy group, condition, diameter, length, thread and quantity, or send the print. Add any coating, testing, PPAP or sour-service requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize requirements from ASTM F593 and F594. The standard itself governs. Check the current edition for your order.