
SAE J429 Grade 5 and Grade 8 Bolts
SAE J429 sets the strength grades for inch-series steel bolts, screws and studs up to 1-1/2 in. diameter. Grade 5 is medium carbon steel, quenched and tempered, at 120 ksi tensile. Grade 8 is medium carbon alloy steel, quenched and tempered, at 150 ksi. The grade is shown by radial lines on the head.
Grade 5 and Grade 8 parts from Eastwood
- Bolts, cap screws and studs to J429 Grade 5 or Grade 8, made to your drawing
- Heat treatment done in house or by outside heat treaters, to the grade's requirements
- Material certifications with heat numbers shipped with the order
- PPAP documentation at Levels 1 to 5, for a fee
- An AS9100D and ISO 9001:2015 certified shop in Houston, Texas
Grades
| Grade | Material | Condition |
|---|---|---|
| 1 | Low or medium carbon steel | As made |
| 2 | Low or medium carbon steel | As made |
| 5 | Medium carbon steel | Quenched and tempered, 800°F minimum temper |
| 5.2 | Low carbon boron steel | Quenched and tempered |
| 8 | Medium carbon alloy steel | Quenched and tempered, 800°F minimum temper |
| 8.2 | Low carbon boron steel | Quenched and tempered |
Strength
| Grade | Size (in.) | Proof load (ksi) | Yield, min (ksi) | Tensile, min (ksi) | Elongation, min (%) | Reduction of area, min (%) | Core hardness, Rockwell |
|---|---|---|---|---|---|---|---|
| 1 | 1/4 to 1-1/2 | 33 | 36 | 60 | 18 | 35 | B70 to B100 |
| 2 | 1/4 to 3/4 | 55 | 57 | 74 | 18 | 35 | B80 to B100 |
| 2 | Over 3/4 to 1-1/2 | 33 | 36 | 60 | 18 | 35 | B70 to B100 |
| 5 | 1/4 to 1 | 85 | 92 | 120 | 14 | 35 | C25 to C34 |
| 5 | Over 1 to 1-1/2 | 74 | 81 | 105 | 14 | 35 | C19 to C30 |
| 5.2 | 1/4 to 1 | 85 | 92 | 120 | 14 | 35 | C26 to C36 |
| 8 | 1/4 to 1-1/2 | 120 | 130 | 150 | 12 | 35 | C33 to C39 |
| 8.2 | 1/4 to 1 | 120 | 130 | 150 | 10 | 35 | C33 to C39 |
Grade 2 values for 1/4 to 3/4 in. apply to bolts 6 in. and shorter and to studs of any length. Longer Grade 2 bolts are held to Grade 1 values.
Head markings
J429 grades are shown by radial lines on the head, with the maker's mark in the center. Grades 1 and 2 have no radial lines. Grade 5 has three lines, 120 degrees apart. Grade 8 has six lines, 60 degrees apart. A quick way to remember it: count the lines and add two. Grades 5.2 and 8.2 have their own head markings, different from Grades 5 and 8; check the current J429 for them.
Strength compared
Above 1-1/2 in.
J429 stops at 1-1/2 in. For larger diameters, the usual ASTM equivalents are:
| J429 grade | ASTM grade for larger sizes |
|---|---|
| Grades 1 and 2 | A307 Grade A |
| Grade 5 | A449 |
| Grade 8 | A354 Grade BD |
Nuts
J429 bolts are normally paired with SAE J995 nuts of the matching grade. For heavy hex nuts in ASTM grades, see ASTM A563.
Grade 5 and 8 compared
| Specification | Typical part | Minimum tensile (ksi) | Heat treated | Size range (in.) |
|---|---|---|---|---|
| A307 Grade A | Bolts, studs, threaded rod | 60 | No | 1/4 to 4 |
| SAE J429 Grade 5 | Bolts, screws, studs | 120 to 1 in.; 105 above | Yes | Up to 1-1/2 |
| A449 | Bolts, studs, any shape | 120 to 1 in.; 105; 90 above 1-1/2 | Yes | 1/4 to 3 |
| F3125 Grade A325 | Heavy hex structural bolts | 120 | Yes | 1/2 to 1-1/2 |
| SAE J429 Grade 8 | Bolts, screws, studs | 150 | Yes | Up to 1-1/2 |
| A354 Grade BD | Bolts, studs | 150 | Yes | 1/4 to 4 |
| F3125 Grade A490 | Heavy hex structural bolts | 150 (173 max) | Yes | 1/2 to 1-1/2 |
| A574 | Socket head cap screws | 180 to 1/2 in.; 170 above | Yes | #0 to 4 |
Metric equivalents
| Inch grade | Closest metric class | Metric minimum tensile |
|---|---|---|
| SAE J429 Grade 5, A449 and F3125 A325 | 8.8 | 800 MPa to M16, 830 MPa above (about 116 to 120 ksi) |
| SAE J429 Grade 8, A354 BD and F3125 A490 | 10.9 | 1,040 MPa (about 151 ksi) |
| A574 socket head cap screws | 12.9 | 1,220 MPa (about 177 ksi) |
The pairs are close in strength, not interchangeable. Metric and inch threads do not mix, and the standards test and mark differently. Grade 5 and A449 match class 8.8 only up to 1 in.; above that they fall below it.
Common questions
What is the difference between Grade 5 and Grade 8 bolts?
Grade 5 is medium carbon steel at 120 ksi minimum tensile up to 1 in. Grade 8 is medium carbon alloy steel at 150 ksi. Both are quenched and tempered. Grade 5 has three radial lines on the head; Grade 8 has six.
How do I tell a Grade 8 bolt from the head?
Six radial lines on the head, 60 degrees apart. Three lines is Grade 5. No radial lines means no strength grade is marked; treat it as Grade 2 or lower only if the paperwork confirms it.
What is the tensile strength of a Grade 8 bolt?
150 ksi minimum, with 130 ksi minimum yield and 120 ksi proof load, from 1/4 to 1-1/2 in.
What size range does SAE J429 cover?
Up to 1-1/2 in. diameter. Above that, A449 is the usual equivalent of Grade 5 and A354 Grade BD of Grade 8.
Are Grade 8 bolts the same as A490?
They have the same minimum tensile and yield strength, but A490 is a structural bolt standard with its own dimensions, testing and coating rules. One is not a substitute for the other without engineering approval.
What material is SAE J429?
Grades 1 and 2 are low or medium carbon steel. Grade 5 is medium carbon steel and Grade 8 is medium carbon alloy steel, both quenched and tempered.
What material is equivalent to SAE J429 grade 5?
ASTM A449 up to 1 in., at the same 120 ksi. Above 1-1/2 in., A449 is the usual call. In metric, property class 8.8 is close.
Is 10.9 equivalent to grade 8?
Close. Class 10.9 is 1,040 MPa (about 151 ksi) minimum tensile; Grade 8 is 150 ksi. They are not interchangeable because the threads differ.
What's harder, grade 8 or grade 5 bolts?
Grade 8. Core hardness is C33 to C39 for Grade 8 against C25 to C34 for Grade 5 up to 1 in.
Is there anything stronger than grade 8 bolts?
Yes. A574 socket head cap screws are 180 ksi minimum tensile up to 1/2 in., and metric class 12.9 is about 177 ksi.
Sizes Eastwood makes
J429 covers up to 1-1/2 in. We machine Grade 5 and Grade 8 bolts, cap screws and studs across that range, and larger parts to A449 or A354 BD.
Related pages
Hex head cap screws · Cap screws · Industrial studs · Custom bolts · Quality, certifications and PPAP
Industries that use this spec: Oil and Gas · Power Generation
Other specification guides: ASTM F1554 anchor rods · ASTM A325 structural bolts · ASTM A193 · A193 Grade B7 · ASTM A194 nuts · ASTM A320 · ASTM A453 Grade 660 · ASTM A354 · ASTM F593 and F594 · ASTM A574 socket head cap screws · ASTM A307 · ASTM A449 · ASTM A563 nuts · ASTM F436 washers · ASTM A490 structural bolts
Quote Grade 5 or Grade 8 parts
Send the grade, diameter, length, thread and quantity, or send the print. Add any coating, testing or PPAP requirement and the date you need the parts. Lead time comes back with the price.
Request a quote sales@emfasteners.com
The tables summarize requirements from SAE J429. The standard itself governs. Check the current edition for your order.